Water Eject Sound
Water eject sound for a wet phone speaker: 165 Hz pulses, 20 seconds a cycle. It may help, and often does nothing.
https://flxcode.com/water-eject/
Use it only on the phone's own speaker, never near your ear. Set your phone volume to about two thirds. Stop if you hear buzzing, crackling or rattling.
Cycle 1 of 3
Stopped
Let it dry
Three cycles are enough for one go. Leave the phone with the speaker facing down on a dry cloth, away from heat, for a few hours. More cycles are unlikely to help.
How does the speaker sound now?
165 Hz in short pulses, 20 seconds a cycle, at most 3 cycles. This protocol is editorial guidance. It may help, and often does nothing.
No sound?
- iPhone: check the ring/silent switch and the media volume.
- Check the system volume and which output is selected (speakers, headphones, Bluetooth).
- Bluetooth headphones switch to call mode while a microphone is open: sound becomes mono and dull.
- A mono audio setting in accessibility makes left and right sound the same. A web page can't detect it.
- Another tab or app may be using the audio. Close it and press Play again.
No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.
Problem or idea? Email us
How to use it
- Take the case off and wipe the phone with a dry cloth.
- Hold the phone with the speaker facing down over a dry towel.
- Set your phone volume to about two thirds. A web page can't set it for you.
- Press Start. The tone runs for 20 seconds and stops by itself.
- Wipe the grille, play a normal sound, then tell the page how the speaker sounds.
- You can run up to 3 cycles. After the third, let the phone dry.
Stop if
- You hear buzzing, crackling or rattling.
- The phone gets warm.
- The sound is uncomfortable.
Press Stop or Esc. If the sound gets worse, do not run it again.
What it can and can't do
The tone may move droplets that sit at the speaker grille, so a muffled voice or music can get clearer. It does not dry the inside of the phone and it does not clear the charging port. Water in the port or behind the grille needs time to dry, often hours.
- Don't hold the phone to your ear while it plays.
- Don't run it while the phone is charging.
- Don't use it on a cracked or damaged speaker.
- Smartwatches have their own water lock. Use the watch's function instead.
After the cycles
If the speaker still sounds muffled, wait. Leave the phone speaker-down on a dry cloth, away from direct heat, for several hours. If it rattles or crackles, check it with the speaker rattle test at low volume. A repair shop is the next step if it stays bad.
Accuracy and limits
The 165 Hz, 20 second, 3 cycle protocol is editorial guidance. We did not find a test that proves a frequency or a time works, so the page does not promise a result. It plays a tone and nothing else: it does not measure water, and it can't tell if your speaker is damaged. For other tones use the tone generator.
How it works
One sine oscillator at 165 Hz in the Web Audio API. Its level switches on and off in pulses of 0.55 seconds on and 0.25 seconds off, with 15 ms ramps at both edges so nothing clicks. The end of the 20 seconds is set on the audio clock, so a busy page can't make it run longer. If the headphones or the output change, it stops. Nothing is recorded or uploaded. We count events without cookies (details).
FAQ
Does water eject sound work?
It may help, and often does nothing. A strong low tone makes the speaker membrane move, and that can push droplets off the grille. It does not dry the inside of the phone or the charging port. Treat it as one small step next to wiping and waiting.
Why 165 Hz and 20 seconds?
It is editorial guidance, not a standard. We found no test that backs a particular frequency or time. 165 Hz is a low note a phone speaker can still play, and 20 seconds in short pulses, at most 3 times, keeps the load on the speaker small.
Can it damage my speaker?
Any loud sound can. That is why the page runs short cycles, stops by itself, caps the count at 3 and asks you to stop at buzzing, crackling or rattling. Keep the volume about two thirds, not at the maximum.
Should I use it while the phone is charging?
No. Do not run it while charging, and do not charge a phone with a wet port. Let it dry first.
Is it for a smartwatch?
No. Smartwatches have their own water lock or eject function in the watch settings. Use that one.
Does anything get uploaded?
No. The tone is made in your browser and nothing is stored. We count events, like how often a cycle ran to the end, without cookies.
More from FLXCode
Speaker Rattle TestNew
Find the frequency where a speaker rattles. A slow 20 to 300 Hz glide you can mark, narrow to a band and repeat.
Speaker TestNew
Phase, sweep and range. A quick check for speakers and headphones.
Tone GeneratorNew
Play any frequency from 1 Hz to 22 kHz. Sine, square, triangle or sawtooth.
Mic TestNew
Check your microphone: level, clipping, a quick recording, and what your browser does to the sound.