Dilution Calculator (C1V1 = C2V2)
Fill in three of the four values and get the fourth, with the solvent to add and the dilution factor.
https://flxcode.com/dilution-calculator/
Example Dilution
Stock volume to take (V1)
| C1 (stock) | 2 M |
|---|---|
| V1 (stock taken) | 50 mL |
| C2 (final) | 0.5 M |
| V2 (final volume) | 200 mL |
| Dilution factor (C1 ÷ C2) | 4 × |
| Solvent to add (V2 − V1) | 150 mL |
The steps, with your numbers
C1 × V1 = C2 × V2
V1 = C2 × V2 ÷ C1 = (0.5 M × 200 mL) ÷ 2 M = 50 mL
Solvent to add = V2 − V1 = 150 mL. Top up to the final volume after adding the stock.
No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.
Problem or idea? Email us
Quick start
- Choose which value to find. Stock volume (V1) is the most common.
- Type the other three and pick a unit for each. Different units are fine.
- Measure V1 of stock into a flask and fill with solvent to V2.
Worked examples
| Find | Given | Answer | Note |
|---|---|---|---|
| V1 | 2 M stock, make 200 mL of 0.5 M | 50 mL | Take this much stock, top up to 200 mL |
| V2 | 2 M stock, 50 mL taken, diluted to 0.5 M | 200 mL | The final volume |
| C2 | 10 mL of 5 M stock made up to 250 mL | 0.2 M | Units match, so no conversion |
| C1 | 1 mL of stock made up to 100 mL gives 25 µM | 0.0025 M | The stock was this strong |
| V1 | Make 1 L of 70% from 95% ethanol | 736.8 mL | % here is w/v, but the same works for v/v |
| V1 | 100 mM stock to 100 µM, 5 mL final (mM to µM) | 5 µL | Different units are converted for you |
| V1 | 10 mg/mL stock to 0.5 mg/mL, 20 mL | 1 mL | Mass concentration |
The formula
C1 × V1 = C2 × V2
Solve it for the value you want:
- V1 = C2 × V2 ÷ C1
- V2 = C1 × V1 ÷ C2
- C1 = C2 × V2 ÷ V1
- C2 = C1 × V1 ÷ V2
It holds because the moles (or grams) of solute, concentration times volume, are the same before and after you add solvent. Both concentrations need the same unit, and both volumes need the same unit. The tool converts for you and shows the line with your numbers.
Serial dilutions
For a series, run the tool once per step, using the result of one step as the stock for the next. Two 1:10 steps give 1:100. A 1:10 step with 1 mL of stock and 9 mL of solvent is V1 = 1 mL, V2 = 10 mL.
Common mistakes
- Mixing units without converting, like C1 in M and C2 in mM. The tool handles it, but a hand calculation is 1000 times off.
- Adding V2 of solvent instead of topping up to V2.
- Putting the stock where the final value goes. C1 is always the stronger one.
- Using the formula for mixing two solutions of different strength. That is a different calculation.
If your stock is a solid you weighed, work out its molarity first with the molarity calculator. The molar mass calculator gives the grams per mole.
Numbers this uses
Every constant the tool uses is listed here with its source. Where a number varies, you can edit it in the tool.
- Molar units is 1 mM = 0.001 M and 1 µM = 0.000001 M. SI prefixes.
- Percent is 1% = 10 mg/mL. Weight per volume: 1 g in 100 mL. Used for % as a mass based unit.
- Volume units is 1 mL = 0.001 L and 1 µL = 0.000001 L. SI prefixes.
- Display is 4 significant figures. Our choice. Your pipette and flask decide how many digits are real.
Nothing you type is uploaded. We count events without cookies (details).
FAQ
What is the dilution formula?
C1 × V1 = C2 × V2. C1 and V1 are the concentration and volume of the stock, C2 and V2 are the concentration and volume you want. The amount of solute is the same before and after, only the solvent changes.
How do I dilute a 2 M solution to 0.5 M?
For 200 mL of 0.5 M, V1 = 0.5 × 200 ÷ 2 = 50 mL of stock. Add 150 mL of solvent, or put 50 mL of stock in a flask and fill to 200 mL. It's a 4 times dilution.
Do I add the solvent volume or top up to the final volume?
Top up to the final volume. The stock and the solvent do not always add up exactly, so measure the stock into the flask and fill to the mark. The "solvent to add" figure is V2 − V1, a guide for the quantity.
What is a dilution factor?
It is C1 ÷ C2, also V2 ÷ V1. A 1:10 dilution means 1 part stock plus 9 parts solvent, which is a dilution factor of 10.
Can I mix units, like mM and µM or mL and L?
Yes. Pick the unit for each box. Concentrations convert to mol/L (or mg/mL for % and mg/mL) and volumes to litres before solving. You cannot mix a molar unit with a mass one, because that needs the molar mass.
What does % mean in the unit list?
Weight per volume: 1% is 1 g per 100 mL, which is 10 mg/mL. For a volume per volume percent, like 70% ethanol, the same formula works as long as both sides are v/v.
Why does it say C2 is higher than C1?
A dilution only lowers the concentration. If the wanted concentration is higher than the stock, you need to add more solute or evaporate solvent, not dilute.
Are my numbers sent anywhere?
No. The calculation runs in your browser, and what you type is not put in the address bar, not stored and not counted.
More from FLXCode
Molarity CalculatorNew
Solve for molarity, mass, moles or volume. Type a formula for the molar mass and see every step with your numbers.
Molar Mass CalculatorNew
Molar mass of any formula, with brackets and hydrates. Shows each element, its atom count and percent by mass.
Chemical Equation BalancerNew
Balance any chemical equation, with charges and hydrates. Whole-number coefficients and an atom count for each side.
Exponent CalculatorNew
Powers with integer, negative and fractional exponents. Integer results are exact, with scientific notation.