Speaker Test
Check that both sides work, are the right way round and are wired in phase.
https://flxcode.com/speaker-test/
Step 1 of 3
Stopped
Each button plays three short bursts of noise. The lamps show the signal sent to each side. Do you hear it only on that side?
Use headphones? Start quiet.
Phone speakers are often mono, so Left and Right sound the same there. Use headphones for this step. The page can't detect a dead speaker, so listen.
For a faster check with spoken labels, use the left and right speaker test.
The same noise plays on both sides. In phase it sounds centred and full. Out of phase it sounds wide and thin.
If it sounds the wrong way round
If the two sound the other way round, one speaker is wired backwards: swap its + and - wires. Out of phase should have weaker bass.
A sine tone glides from 20 Hz to 20 kHz in 20 seconds. Notice where sound starts, and listen for rattles or buzzing.
20 Hz
sub-bass
Start quiet. Extreme tones can hurt.
High and low tones can be uncomfortable or damage small speakers. Keep the volume low. Above 8 kHz the page lowers the level on its own.
dBFS is the level in the file, not how loud it is at your ear.
Hear a rattle? Slow it down with the speaker rattle test (20 to 300 Hz).
Your result
Start quiet, turn up slowly. Nothing is uploaded: the sound is made in your browser.
No sound?
- iPhone: check the ring/silent switch and the media volume.
- Check the system volume and which output is selected (speakers, headphones, Bluetooth).
- Bluetooth headphones switch to call mode while a microphone is open: sound becomes mono and dull.
- A mono audio setting in accessibility makes left and right sound the same. A web page can't detect it.
- Another tab or app may be using the audio. Close it and press Play again.
No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.
Problem or idea? Email us
Quick start
- Turn your device volume down. The test starts at 10%.
- Left / right: press Left, Right and Both. The matching side should light up and play. For a quicker check, use the left and right speaker test.
- Phase: play In phase, then Out of phase. In phase should sound centred and fuller.
- Sweep: play the 20-second sweep and listen for where sound starts, rattles or fades out. To find the exact frequency of a rattle, use the speaker rattle test.
- Press Sounds right or Something's wrong after each step. Stop at any time with the Stop button or Esc.
What you should hear
| Test | Good | Problem |
|---|---|---|
| Left | Sound only on the left, three short bursts. | Sound on the right, on both, or nothing. |
| Right | Sound only on the right. | Sound on the left, on both, or nothing. |
| In phase | Centred, full, solid bass. | Wide or hollow, bass missing. |
| Out of phase | Wide, diffuse, thinner bass. | Sounds the same as In phase, or better. |
| Sweep | Smooth rise, no rattles or buzz. | Rattle, buzz, gaps or sudden drops. |
Troubleshooting
- Left and right are swapped: swap the cables or the earbuds. Check the balance setting in your system sound settings.
- Only one side plays: check the balance slider, the cable and the plug. On a phone, turn off Mono audio in the accessibility settings.
- Both sides play the same: Mono audio may be on, or you are using a single phone speaker.
- Out of phase sounds better: one speaker has its + and - wires swapped. Reverse them on one speaker.
- Bluetooth: the first second can be cut off while the link wakes up. Play again. Some Bluetooth modes mix to mono.
- No sound on iPhone: check the ring/silent switch and the media volume.
- Rattle in the sweep: a loose part, a speaker grille or a shelf. Note the frequency where it starts, or pin it down with the rattle test.
Accuracy and limits
This is a setup check, not a measurement. It does not do room calibration, loudness in dB, frequency response (that needs a microphone) or surround sound. The phase test is by ear, so it works best with two speakers placed in front of you or with headphones. The sweep ends at 20 kHz, or lower if your audio device runs at a low sample rate. For one steady frequency use the tone generator. Above 8 kHz the sweep is quieter, so its output stays at or below -20 dBFS. dBFS is the level in the file, not how loud it is at your ear. To check the other half of a headset, try the mic test.
How it works
The page makes one pink-noise buffer and plays it through the Web Audio API on one or both channels. For the out-of-phase test the right channel is multiplied by -1. Every burst fades in and out over 15 ms, so starting and stopping never clicks. The sweep is a sine tone with an exponential frequency ramp. Nothing is recorded or uploaded. We count events without cookies (details).
FAQ
How do I know if my speakers are in phase?
Play the in-phase and out-of-phase buttons. In phase, the noise sounds centred, full and solid. Out of phase, it sounds wide, hollow or inside your head, with thin bass. If the two are the other way round, one speaker has its + and - wires swapped.
Why do Left and Right sound the same on my phone?
Most phones have one speaker, or two that play the same signal. Plug in headphones to check the two sides.
What is the sweep for?
It shows where a speaker starts to produce sound at the low end, where it rattles or buzzes, and where you stop hearing it at the top. Small speakers give up well above 20 Hz, and most adults stop hearing somewhere above 15 kHz.
Is this a calibrated test?
No. The volume is not in dB, and your device is not measured. It tells you whether the setup works, not how accurate it is. The Left and Right lamps show the signal the page sends to each side. They cannot tell you whether a speaker is dead, so use your ears.
Why does it use pink noise?
Pink noise has equal energy in each octave, so it sounds even and is easy to place in the room. A pure tone is harder to locate, and bursts of noise make left and right obvious.
Does anything get uploaded?
No. The sound is generated in your browser. We count events, like which test you played, without cookies.
More from FLXCode
Left and Right Speaker TestNew
Press Left, Right and Both, then tell the page what you heard. Works with speakers and headphones.
Speaker Rattle TestNew
Find the frequency where a speaker rattles. A slow 20 to 300 Hz glide you can mark, narrow to a band and repeat.
Tone GeneratorNew
Play any frequency from 1 Hz to 22 kHz. Sine, square, triangle or sawtooth.
Water Eject SoundNew
A 165 Hz pulsed tone you can play on a wet phone speaker: 20 seconds a cycle, 3 cycles at most, with a stop button.