FLXCode Tile Calculator

FLXCode apps

Appearance

Tile Calculator

Enter the floor or wall size and the tile size. You get the number of tiles and boxes, with the grout joint and waste counted.

Floor or wall

Example straight lay lay, 10% waste

65 tiles to buy

Tile counts
Boxes9 (144 sq ft in total)
Area120 sq ft
Area with waste132 sq ft
Tiles with no waste60

The sums

  • One tile with its joint2.0314 sq ft
  • 132 sq ft / 2.0314 sq ft, rounded up65 tiles

Boxes are counted by area, so the last box may hold a few more tiles than you need. Keep them as spares for repairs.

No ads. No account. Nothing you type or record is uploaded. We count page events with a daily code. Check it.

Problem or idea? Email us

Quick start

  1. Type the length and width of each area in feet. Use Add area for an L-shaped or split room.
  2. Pick the tile size from the list, or type your own width and length.
  3. Set the grout joint and the layout. Diagonal and herringbone raise the waste to 15%.
  4. Enter the square feet per box from the label to get the box count.

Worked examples

Computed by the same engine as the tool above.

JobAreaWasteTilesBoxes
Bathroom floor, 8 x 5 ft, 12 x 12 in tile40 sq ft10%443
Kitchen floor, 12 x 10 ft, 12 x 24 in tile120 sq ft10%659
Kitchen floor on the diagonal, same size120 sq ft15%689
Backsplash, 10 x 3 ft, 3 x 6 in subway30 sq ft10%2564
Shower wall, 8 x 3 ft, 4 x 4 in tile24 sq ft10%2245

The formula

tile area = (width + joint) x (length + joint) / 144 in sq ft, with sizes in inches

tiles = area x (1 + waste) / tile area, rounded up

boxes = area x (1 + waste) / sq ft per box, rounded up

In metric the tile is in centimetres, the joint in millimetres and the box in square metres.

Numbers this uses

Every constant the tool uses is listed here with its source. Where a number varies, you can edit it in the tool.

  • Waste, straight lay is 10%. cuts at walls, chipped tiles, a few spares for repairs; editable.
  • Waste, diagonal or herringbone is 15%. more cut tiles along the edges; editable.
  • Grout joint is 1/8 in. a common width for floor tile; each tile takes its size plus one joint.
  • Box size is 16 sq ft. a typical box of 12 x 24 in tile (8 tiles); boxes vary, so read the label and edit it.
  • Square foot is 144 sq in. 12 in x 12 in.

Which layout, which waste

  • Straight (grid): the simplest. Cuts happen only at walls and around fixtures.
  • Offset or brick pattern: close to straight, but plank tiles waste a bit more at the ends. Use 10 to 15%.
  • Diagonal: every edge tile is cut at an angle, so the offcuts are not reusable. Use 15%.
  • Herringbone: the most cuts of all. Start at 15% and go up for small rooms.

Common mistakes

  • Counting boxes from the tile count. Box sizes vary, so work from the area on the label.
  • Forgetting the area under cabinets you may remove later. It is better to tile under them.
  • Expecting more than tiles. This tool counts tiles and boxes only, not the underlayment, the thinset or the grout.
  • Mixing inches and centimetres. Use the unit switch rather than converting by hand.

Your sizes stay in this page and are not uploaded. We count events without cookies (details).

FAQ

How many tiles do I need for a floor?

Divide the floor area by the area of one tile, joint included, and round up. A 12 x 10 ft floor is 120 sq ft. A 12 x 24 in tile with a 1/8 in joint takes 2.031 sq ft, so it needs 60 tiles. With 10% waste it is 65.

How much waste should I add for tile?

10% for a straight grid and 15% for diagonal or herringbone, because more tiles are cut at the edges. Add 5 to 10% more for a small room with many cuts, large tiles or a pattern you need to match. The tool lets you set any number.

How many boxes of tile do I need?

Boxes are counted by area. The kitchen example needs 132 sq ft with waste, which is 9 boxes at 16 sq ft each. On the diagonal it is 9 boxes. Check the sq ft on your own box, since sizes differ.

Do I count the grout joint?

Yes. Each tile takes up its size plus one joint on each side, so a 12 x 12 in tile with a 1/8 in joint uses 12.125 x 12.125 in. On a big floor with thin joints the difference is small. On small mosaic tiles it matters.

Should I buy extra tiles for later?

Yes. Keep a box or at least a few tiles. A tile that breaks in five years may no longer be made, and the dye lot can differ from a new order. The waste you buy now often covers this.

How do I measure a room that is not a rectangle?

Split it into rectangles and add each one with Add area. For an L-shaped room that is two rectangles. Do not measure the whole outline as one box, because you would count the missing corner.

Can I use it for walls and backsplashes?

Yes. Enter the width and height of each wall as length and width. Subtract windows or doors by leaving them out when you split the wall into rectangles.

Is anything I type uploaded or saved?

No. The sums run in your browser. Your sizes are not put in the address bar, not stored and not counted. Only your choice of US or metric units is remembered in this browser.

More from FLXCode

Share Tile Calculator